Mechanical converter from a microwave oven motor

Mechanical converter from a microwave oven motor

The converter we are talking about does not contain a single radio element. Built entirely on two electric motors, one of which was taken from a microwave oven. The conversion principle is very simple: a low-voltage motor is supplied with direct current. This motor rotates a high-voltage motor (acting as a generator), as a result it produces an alternating voltage of up to 500 V at the output.

Will need


  • Plexiglas stand.
  • Clamp terminals.
  • Wires.
  • Motor 12-24 V.
  • Microwave motor (used to rotate the dish).

Mechanical converter from a microwave oven motor

As you can see, the microwave motor is designed for a voltage of 250 V, its power is 4 W. These are, of course, consumed values. If we use it as a generator, the readings will be slightly different; more precisely, they will depend on the frequency of its rotation.

Manufacturing of high voltage converter


The microwave motor also contains a gearbox that needs to be removed. We bend the bent clamps and remove the gearbox along with the rotor on permanent magnets.
Mechanical converter from a microwave oven motor

This rotor must be placed on the shaft of the drive motor.
Mechanical converter from a microwave oven motor

We fix everything on a plexiglass stand so that the axes of the motors are in the same plane without distortion. We connect the wires, connect the terminals for a convenient connection.

Tests


We supply the low-voltage motor with a constant voltage of 24 V (the maximum for it). As you can see, at idle the generator produces more than 300 V. It reaches 500 if you slightly increase the speed by raising the voltage.
Mechanical converter from a microwave oven motor

Now we look under the load, which is a 220 V LED lamp with a power of 5 W.
Mechanical converter from a microwave oven motor

As you can see, the voltage dropped significantly, almost 3 times.
Mechanical converter from a microwave oven motor

The driving motor consumes 0.2 A at 24 V, resulting in a power consumption of 4.8 W. But there is no such power at the output; it is significantly lower. This suggests that the converter itself has low efficiency.

Application


In principle, it is always there. For example, if you take a 12 V motor and use a cell phone charger as a load, you can easily charge your cell phone from a battery.

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (4)
  1. Izhat
    #1 Izhat Guests 22 September 2019 13:41
    0
    Some electric motors (microwaves) operate from 36 V AC through a resistor. There are also 24-26 V.
  2. Vita
    #2 Vita Guests September 26, 2019 09:27
    0
    How do you estimate the output power?
  3. Guest
    #3 Guest Guests December 3, 2019 07:17
    0
    as old as time. in tube radio engineering this device was called an umformer
  4. Hayk
    #4 Hayk Guests February 28, 2021 00:35
    0
    It can’t be the other way around for me, I gain in power; under load, the engine, on the contrary, accelerates; fact, I can send a video for those who doubt it!!!!!!