Wedding pillow with rose
It’s hard to surprise anyone with a wedding in black and white. Newlyweds strive to make their holiday not only unforgettable, but also unique. Therefore, more and more often, celebrations are dedicated to some theme - sea, olive, birch. Young people with a particularly bright temperament have pink weddings, in which red is used everywhere, a symbol of fiery love and roses, denoting sensuality and tenderness. For a pink wedding, all accessories should be unusual. I would like to clearly demonstrate to you how to create a red pillow with a rose for presenting wedding rings.
You will need a piece of red fabric 35 by 20 cm, thread, cotton wool, white ribbon, white mesh and a wide (5 cm) satin ribbon to create a rose. For the petals, purchase some green ribbon. Use hot glue to secure the rose petals. The rosette is made using the technique kanzashi, to create such petals you can use tweezers and a lighter or a metal ruler with a soldering iron; to work with a hot soldering iron you need glass. When everything is prepared, let's start creating the pillow. Sew the fabric on three sides.
Then stuff it with cotton wool or other soft material. Don't pack it tightly, otherwise the rings will just roll off.
Sew up the fourth side of the pillow.
Now we trim the edge of the pillow with white satin ribbon. A width of 4 cm is suitable. Make clothespins every 4 cm by 2 cm.
You can pin the folds first, and then overcast everything
From the middle tape, sew a figure eight into the corner.
Cover the rest of the area with a net. It can be sewn or glued.
Let's start creating a rose. Mode: tape for 50 squares, their size is 5 cm. You can cut it with either a soldering iron or scissors, but with further melting of the edges over a lighter.
Bend the square as in the picture.
Next, you need to bend one edge so that the corner is in the center of the bottom side. Then fold the other edge in the same way.
To create a petal for a rose, you need to cut off the base and solder all the layers, in the end we get the following blanks:
We twist the first petal - this is a rosebud.
Next, glue the petals one after another in a spiral. Be sure to try to give the rose an even appearance, do not make the middle of the flower protrude or fall in.
The reverse side of the flower is glued in one plane.
Let's start creating green sheets. To do this, take a grass-colored ribbon and use scissors to cut out petals that resemble the original ones of a rose flower.
Scorch them over the flame, bend them more often. That is, they scorched 2 cm and bent them with their fingers.
The sheets should take on a more voluminous appearance.
Warm up the knife and press the veins of the leaves onto the towel.
The leaves should look like this
Glue leaves to create a composition
Now glue or sew on the rose. Be sure to use your hands to press a hole in the cotton wool in the middle of the pillow to place the rings there.
You will need a piece of red fabric 35 by 20 cm, thread, cotton wool, white ribbon, white mesh and a wide (5 cm) satin ribbon to create a rose. For the petals, purchase some green ribbon. Use hot glue to secure the rose petals. The rosette is made using the technique kanzashi, to create such petals you can use tweezers and a lighter or a metal ruler with a soldering iron; to work with a hot soldering iron you need glass. When everything is prepared, let's start creating the pillow. Sew the fabric on three sides.
Then stuff it with cotton wool or other soft material. Don't pack it tightly, otherwise the rings will just roll off.
Sew up the fourth side of the pillow.
Now we trim the edge of the pillow with white satin ribbon. A width of 4 cm is suitable. Make clothespins every 4 cm by 2 cm.
You can pin the folds first, and then overcast everything
From the middle tape, sew a figure eight into the corner.
Cover the rest of the area with a net. It can be sewn or glued.
Let's start creating a rose. Mode: tape for 50 squares, their size is 5 cm. You can cut it with either a soldering iron or scissors, but with further melting of the edges over a lighter.
Bend the square as in the picture.
Next, you need to bend one edge so that the corner is in the center of the bottom side. Then fold the other edge in the same way.
To create a petal for a rose, you need to cut off the base and solder all the layers, in the end we get the following blanks:
We twist the first petal - this is a rosebud.
Next, glue the petals one after another in a spiral. Be sure to try to give the rose an even appearance, do not make the middle of the flower protrude or fall in.
The reverse side of the flower is glued in one plane.
Let's start creating green sheets. To do this, take a grass-colored ribbon and use scissors to cut out petals that resemble the original ones of a rose flower.
Scorch them over the flame, bend them more often. That is, they scorched 2 cm and bent them with their fingers.
The sheets should take on a more voluminous appearance.
Warm up the knife and press the veins of the leaves onto the towel.
The leaves should look like this
Glue leaves to create a composition
Now glue or sew on the rose. Be sure to use your hands to press a hole in the cotton wool in the middle of the pillow to place the rings there.
Similar master classes
Particularly interesting
Comments (1)
