DIY graduation bracelet
Ah, this is graduation night! A holiday of sadness and joy. In the life of every student, graduation party is the most significant and most solemn day. And girls with pigtails are now beautiful girls who shine with their beauty and tenderness. Once you've chosen the perfect prom dress, it's time to find the right accessories to complement the perfect outfit and create a chic, exciting look. Therefore, I propose to make a bracelet that will give the look a finished look and a unique style.
To create a bracelet we will need:
Step 1. First, measure the wrist of the person for whom the bracelet is intended. In this case, the size is approximately 17 cm. Then we take the chain, fold it in half and measure 17 cm; it will be more convenient if you use a tailor’s tape.
Step 2.Then we thread a ring through one end of the chain and close it with pliers.
Step 3. Take the second ring and thread a carabiner clasp into it. Next, we thread the carabiner with the ring into the other end of the chain.
Step 4. As a result, the chain should be double. On one side of the chain there is a ring, and on the other there is a ring with a carabiner.
Step 5. On a small piece of plastic from the container, we outline a flat stone made to look like marble (such a stone can be bought at any craft store) and cut it out, you get a plastic blank. This is done so that when we glue the stone, it is securely fastened.
Step 6. For beauty, glue rhinestones on a ribbon along the contour of the stone.
Step 7. All that remains is to glue everything. We take a pre-cut piece of plastic and glue it under the chain. Keep in mind that the chain should be wide apart as shown below.
Step 8. Glue the stone on top of the plastic blank.
Step 9. Glue the half beads. The distance between them should be the same. You can use more or less half beads, and the color of the stone depends on your taste or the color of the dress.
Here we have such a delicate and romantic bracelet! Thanks to this bracelet you will definitely not be left without attention.
To create a bracelet we will need:
- - chain;
- - rhinestones on the ribbon;
- - a flat stone for jewelry, made to look like marble;
- - four half beads (2 large and 2 small);
- - clasp - carbine for bracelet and two rings;
- - wire cutters and pliers;
- - scissors;
- - Moment glue;
- - a small piece of plastic from the container;
- - permanent marker or felt-tip pen.
Step 1. First, measure the wrist of the person for whom the bracelet is intended. In this case, the size is approximately 17 cm. Then we take the chain, fold it in half and measure 17 cm; it will be more convenient if you use a tailor’s tape.
Step 2.Then we thread a ring through one end of the chain and close it with pliers.
Step 3. Take the second ring and thread a carabiner clasp into it. Next, we thread the carabiner with the ring into the other end of the chain.
Step 4. As a result, the chain should be double. On one side of the chain there is a ring, and on the other there is a ring with a carabiner.
Step 5. On a small piece of plastic from the container, we outline a flat stone made to look like marble (such a stone can be bought at any craft store) and cut it out, you get a plastic blank. This is done so that when we glue the stone, it is securely fastened.
Step 6. For beauty, glue rhinestones on a ribbon along the contour of the stone.
Step 7. All that remains is to glue everything. We take a pre-cut piece of plastic and glue it under the chain. Keep in mind that the chain should be wide apart as shown below.
Step 8. Glue the stone on top of the plastic blank.
Step 9. Glue the half beads. The distance between them should be the same. You can use more or less half beads, and the color of the stone depends on your taste or the color of the dress.
Here we have such a delicate and romantic bracelet! Thanks to this bracelet you will definitely not be left without attention.
Similar master classes
Particularly interesting
Comments (1)
