Strawberry hair clips
Hairpins with voluminous berries can easily decorate a girl's hairstyle in the summer season. And if you choose a red or white dress to go with them, it will be a sight to behold.
To make a pair of hairpins you need:
- red ribbon 5 cm wide, cut 28 cm;
- green ribbon 3 cm 12 cm wide;
- rope with lurex 25 cm;
- yellow thread;
- felt base 2 pcs.;
- satin ribbon 2.5 wide white 1 m;
- yellow stamens 60 pcs;
- seaming lid or other with a diameter of 7 cm;
- green ribbon 4 cm 50 cm wide;
- padding polyester.
Berries.
For one berry you will need a piece of red tape 7 cm long. We apply the lid and draw it with a soldering iron or draw an outline with a pen. You need to get a semicircle, cut it out and secure the edge over the fire.
Now we take a thread with a needle and sew short stitches over the entire surface of the workpiece, simulating seeds.
Now we fold the workpiece in half and sew one edge, you should get a cone with a hole at the base.
We turn the workpiece inside out and fill it with padding polyester. Sew along the top edge with small stitches and tighten the part. A berry is formed.
Now, using a hoop, we cut out the sepals by eye.
You can cut it with scissors and secure all the cuts by quickly passing it through a candle flame.
We make a hole in the center of the sepal. We take a piece of string intended for the stem, thread it through the hole in the sepal and glue the string in the middle of the berry. Now we grease the top of the berry with glue and glue the sepals.
We do this for the remaining 3 berries. The berries must be connected to each other in pairs.
Leaves.
For the leaves, cut out 4 by 5 pieces from green satin ribbon, fold them in half and cut out an oval leaf according to the shape.
Next, we use scissors to form a leaf like the corresponding berry and secure it over the fire. We fold the leaf in half lengthwise, fix it with tweezers and make a vein, then fold it and make the side veins.
Flowers.
For the flower you need to make round petals kanzashi from pieces of white tape 2.5 by 2.5 cm.
To do this, fold the square diagonally, then in half again, hold it by the fold and turn the corners in the opposite direction, hold it with tweezers and secure the corner over the fire.
For each flower you need 6 petals, on each hairpin there are 3 flowers. As a result, the total number of petals is 36 pieces.
To assemble the flower, glue the leaves at the corner, before gluing the outer ones, insert a bunch of 10 stamens into the center and secure with glue.
Assembling the hairpin.
Lubricate the felt circle with glue and glue the leaves with a fan.
Next, glue a bunch of 3 flowers and between them a twig with 2 berries.
The arrangement of strawberries is ready, all you have to do is glue the clip on the back and you can go for a walk.
To make a pair of hairpins you need:
- red ribbon 5 cm wide, cut 28 cm;
- green ribbon 3 cm 12 cm wide;
- rope with lurex 25 cm;
- yellow thread;
- felt base 2 pcs.;
- satin ribbon 2.5 wide white 1 m;
- yellow stamens 60 pcs;
- seaming lid or other with a diameter of 7 cm;
- green ribbon 4 cm 50 cm wide;
- padding polyester.
Berries.
For one berry you will need a piece of red tape 7 cm long. We apply the lid and draw it with a soldering iron or draw an outline with a pen. You need to get a semicircle, cut it out and secure the edge over the fire.
Now we take a thread with a needle and sew short stitches over the entire surface of the workpiece, simulating seeds.
Now we fold the workpiece in half and sew one edge, you should get a cone with a hole at the base.
We turn the workpiece inside out and fill it with padding polyester. Sew along the top edge with small stitches and tighten the part. A berry is formed.
Now, using a hoop, we cut out the sepals by eye.
You can cut it with scissors and secure all the cuts by quickly passing it through a candle flame.
We make a hole in the center of the sepal. We take a piece of string intended for the stem, thread it through the hole in the sepal and glue the string in the middle of the berry. Now we grease the top of the berry with glue and glue the sepals.
We do this for the remaining 3 berries. The berries must be connected to each other in pairs.
Leaves.
For the leaves, cut out 4 by 5 pieces from green satin ribbon, fold them in half and cut out an oval leaf according to the shape.
Next, we use scissors to form a leaf like the corresponding berry and secure it over the fire. We fold the leaf in half lengthwise, fix it with tweezers and make a vein, then fold it and make the side veins.
Flowers.
For the flower you need to make round petals kanzashi from pieces of white tape 2.5 by 2.5 cm.
To do this, fold the square diagonally, then in half again, hold it by the fold and turn the corners in the opposite direction, hold it with tweezers and secure the corner over the fire.
For each flower you need 6 petals, on each hairpin there are 3 flowers. As a result, the total number of petals is 36 pieces.
To assemble the flower, glue the leaves at the corner, before gluing the outer ones, insert a bunch of 10 stamens into the center and secure with glue.
Assembling the hairpin.
Lubricate the felt circle with glue and glue the leaves with a fan.
Next, glue a bunch of 3 flowers and between them a twig with 2 berries.
The arrangement of strawberries is ready, all you have to do is glue the clip on the back and you can go for a walk.
Similar master classes
Particularly interesting
Comments (0)
